3 data shee t array chip resistors yc/tc 164 (8pin/4r; pb free) 5%, 1% sizes 4 0603 product specification ? mar 01, 2005 v.2 supersedes date of mar. 06, 2003
series yc/tc 164 (pb free) product specification 2 8 w ww.yageo.com mar 01, 2005 v.2 chip resistor surface mount ctc code yc 164 ? x x x xx xxxx l tc (1) (2) (3) (4) (5) (6) ( 1 ) tolerance f = 1% j = 5% ( 2 ) packaging type r = paper/pe taping reel ( 3 ) temperature coefficient of resistance ? = base on spec ( 4 ) taping reel 07 = 7 inch dia. reel 13 = 13 inch dia. reel ( 5 ) resistance value 56r, 560r, 5k6, 56k, 1m 0r = jumper (6) resistor terminations l = lead free terminations (pure tin) o rdering example the ordering code of a yc164 convex chip resistor array, value 1,000 x with 5% tolerance, supplied in 7-inch tape reel is: yc164-jr-071kl. (1) the resistors have a 12-digit ordering code starting with 2350. (2) the subsequent 4 or 5 digits indicate the resistor tolerance and packaging. (3) the remaining 4 or 3 digits represent the resistance value with the last digit indicating the multiplier as shown in the table of ?last digit of 12nc?. (4) ?l? means lead-free terminations. o rdering example the ordering code of an arv241 convex chip resistor array, value 1,000 x with 5% tolerance, supplied in tape of 5,000 units per reel is: 235003510102l. p p h h y y c c o o m m p p o o r r d d e e r r i i n n g g c c o o d d e e 12nc code 2350 xxx xx xxx l (1) (2) (3) ( 4 ) paper / pe tape on reel (units) (2) type/ 40603 start in (1) tol. (%) resistance range 5,000 20,000 arv241 2350 5% 10 to 1 m ? 035 10xxx 035 12xx x arv242 2350 1% 10 to 1 m ? 025 1xxxx 025 3xxx x arc241 2350 5% 10 to 1 m ? 034 10xxx 013 3xxx x arc242 2350 1% 10 to 1 m ? 024 1xxxx 013 3xxx x jumper 2350 - 0 ? arv241/yc164 035 91001 - arc241/tc164 034 91001 - scope this specification describes yc164 (convex) and tc164 ( concave) series chip resistor arrays with lead-free terminations made by thick film process. ordering information part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and resistance value. note 1. the ?l? at the end of the code is only for ordering. on th e reel label, the standard ctc or 12nc will be mentioned an additi onal stamp ?lfp?= lead free production. 2. products with lead in terminations fulfil the sa me requirements as mentioned in this datasheet. 3. products with lead in terminations will be phased out in the coming months (before july 1st, 2006) resistance decade (3) last digit 0.01 to 0.0976 x 0 0.1 to 0.976 x 7 1 to 9.76 x 8 10 to 97.6 x 9 100 to 976 x 1 1 to 9.76 k x 2 10 to 97.6 k x 3 100 to 976 k x 4 1 to 9.76 m x 5 10 to 97.6 m x 6 example: 0.02 x = 0200 or 200 0.3 x = 3007 or 307 1 x = 1008 or 108 33 k x = 3303 or 333 10 m x = 1006 or 106 last digit of 12nc
series yc/tc 164 (pb free) product specification 3 8 w ww.yageo.com mar 01, 2005 v.2 chip resistor surface mount protective coat. finally, the eight external term inations (pure tin) are added. see fig. 2. construction the resistors are constructed out of a high-grade ceramic body. internal metal electrodes are added at each end and connected by a resistive paste. the composition of the paste is adjusted to give the approximate required resistance and laser cutting of this resistive layer that achieves tolerance trims the value. the resistive layer is covered with a dimensions type yc164 tc164 b (mm) 0.30 0.15 0.30 0.15 h (mm) 0.65 0.05 --- p (mm) 0.80 0.05 0.80 0.05 l (mm) 3.20 0.15 3.20 0.15 h 2 (mm) 0.50 0.15 0.60 0.15 t (mm) 0.60 0.10 0.60 0.10 w 1 (mm) 0.30 0.15 0.30 0.15 w 2 (mm) 1.60 0.15 1.60 0.15 protective coat resistor layer inner electrode end termination ceramic substrate ynsc053 fig. 2 chip resistor construction table 1 marking yc164 e-24 series: 3 digits first two digits for significant figu re and 3rd digit for number of zeros for marking codes, please see eia-marking code rules in data sheet ?chip resistors marking?. fig. 1 value = 240 k ? 2 ynsc029 schematic ynsc055 r1 r2 r3 r4 12 87 3 6 4 5 r1 r1 = r2 = r3 = r4 tc164 yc164 r2 r3 r4 12 87 3 6 4 5 fig. 4 equivalent circuit diagram for dimension see fig. 2 and table 1 a a p l concave termination tc164 yc164 b ynsc054 h 2 h 2 h a a p l convex termination b t w 1 w 2 fig. 3 y c/tc164 series chip resistors dimension for dimension see table 1
series yc/tc 164 (pb free) product specification 4 8 w ww.yageo.com mar 01, 2005 v.2 chip resistor surface mount electrical characteristics characteristics yc/tc164 1/16 w operating temperature range ?55 c to +155 c maximum working voltage 50 v maximum overload voltage 100 v dielectric withstanding voltage 100 v number of resistors 4 5% (e24) 10 ? to 1 m ? 1% (e24/e96) 10 ? to 1 m ? resistance range zero ohm jumpe r < 0.05 ? temperature coefficient 200 ppm/c jumper criteria rated current 1.0 a footprint and soldering profiles for recommended footprint and soldering profiles, please see the special data sheet ?chip resistors mounting?. environmental data for material declaration information (imds-data) of the products, please see the separated info ?environmental data" conformed to eu rohs. table 2 mra632 70 100 ? 55 50 t amb ( c) (%p rated ) 0 0 50 100 155 p max fig. 5 maximum dissipation (p max ) in percentage of rated power as a function of the operating ambient temperature (t amb ) functional description p p o o w w e e r r r r a a t t i i n n g g yc/tc164 rated power at 70c is 1/16 w r ated voltage the dc or ac (rms) continuous working voltage corresponding to the rated power is determined by the following formula: v = (p x r) where v = continuous rated dc or ac (rms) working voltage (v) p = rated power (w) r = resistance value ( x ) packing style and p a ckaging quantity product type packing style reel dimension quantity per reel yc/tc164 paper / pe taping reel (r) 7" (178 mm) 5,000 units 13" (330 mm) 20,000 units note 1. for paper/pe tape and reel specification/dimensions , please see the special data sheet ?packing? document. table 3 packing style and packaging quantity
series yc/tc 164 (pb free) product specification 5 8 w ww.yageo.com mar 01, 2005 v.2 chip resistor surface mount tests and requirements test test method procedure requirements at +25/?55 c and +25/+125 c temperature coefficient o f resistance (t.c.r.) mil-std-202f-method 304; jis c 5202-4.8 formula: t.c.r = ------------------------- 1 0 6 (ppm/c) where t 1 = +25 c or specified room temperature t 2 = ?55 c or +125 c test temperature r 1 = resistance at reference temperature in ohms r 2 = resistance at test temperature in ohms refer to table 2 thermal shoc k mil-std-202f-method 107g; iec 60115-1 4.19 at ?65 (+0/?10) c for 2 minutes and at +155 (+10/?0) c for 2 minutes; 25 cycles (0.5% +0.05 ? ) for 1% tol. (1.0% +0.05 ? ) for 5% tol. low temperature operation mil-r-55342d-para 4.7.4 at ?65 (+0/?5) c for 1 hour; rcwv applied fo r 45 (+5/?0) minutes (0.5% +0.05 ? ) for 1% tol . (1.0% +0.05 ? ) for 5% tol. no visible damage short time overload mil-r-55342d-para 4.7.5; iec 60115-1 4.13 2.5 rcwv applied for 5 seconds at room temperature (1.0% +0.05 ? ) for 1% tol. (2.0% +0.05 ? ) for 5% tol. no visible damage insulation resistance mil-std-202f-method 302; iec 60115-1 4.6.1.1 rcov for 1 minute type yc/tc164 voltage (dc) 100 v 10 g ? dielectric withstand voltage mil-std-202f-method 301; iec 60115-1 4.6.1.1 maximum voltage (v rms ) applied for 1 minute type yc/tc164 voltage (ac) 100 v rms no breakdown or flashover resistance to soldering heat mil-std-202f-method 210c; iec 60115-1 4.18 unmounted chips; 260 5 c for 10 1 seconds (0.5% +0.05 ? ) for 1% tol. (1.0% +0.05 ? ) for 5% tol. no visible damage life mil-std-202f-method 108a; iec 60115-1 4.25.1 at 70 2 c for 1,000 hours; rcwv applied for 1.5 hours on and 0.5 hour off (1% +0.05 ? ) for 1% tol. (3% +0.05 ? ) for 5% tol. r 2 ? r 1 r 1 (t 2 ? t 1 ) table 4 test condition, procedure and requirements
series yc/tc 164 (pb free) product specification 6 8 w ww.yageo.com mar 01, 2005 v.2 chip resistor surface mount test test method procedure requirements solderabilit y mil-std-202f-method 208a; iec 60115-1 4.17 solder bath at 245 3 c dipping time: 2 0.5 seconds well tinned ( 95% covered) no visible damage bending strength jis c 5202.6.14; iec 60115-1 4.15 resistors mounted on a 90 mm glass epoxy resin pcb (fr4) bending: 1 mm (1.0% +0.05 ? ) for 1% tol. (1.0% +0.05 ? ) for 5% tol. no visible damage resistance to solvent mil-std-202f-method 215; iec 60115-1 4.29 lsopropylalcohol (c 3 h 7 oh) or dichloromethane (ch 2 cl 2 ) followed by brushing no smeared noise jis c 5202 5.9; iec 60115-1 4.12 maximum voltage (v rms ) applied. resistors range v alue r < 100 ? 10 db 100 ? r < 1 k ? 20 db 1 k ? r < 10 k ? 30 db 10 k ? r < 100 k ? 40 db 100 k ? r < 1 m ? 46 db 1 m ? r 22 m ? 48 db humidit y (steady state) jis c 5202 7.5; iec 60115-8 4.24.8 1,000 hours; 40 2 c; 93(+2/?3)% rh rcwv applied for 1.5 hours on and 0.5 hour of f (0.5% +0.05 ? ) for 1% tol. (2.0% +0.05 ? ) for 5% tol. leaching eia/is 4.13b; iec 60115-8 4.18 solder bath at 260 5 c dipping time: 30 1 seconds no visible damage intermittent overload jis c 5202 5.8 at room temperature; 2.5 rcwv applied for 1 second on and 25 seconds off; total 10,000 cycles (1.0% +0.05 ? ) for 1% tol. (2.0% +0.05 ? ) for 5% tol. resistance to vibration on request on request moisture resistance heat mil-std-202f-method 106f; iec 60115-1 4.24.2 42 cycles; total 1,000 hours shown as fig. 6 (0.5% +0.05 ? ) for 1% tol. (2.0% +0.05 ? ) for 5% tol. no visible damage
series yc/tc 164 (pb free) product specification 7 8 w ww.yageo.com mar 01, 2005 v.2 chip resistor surface mount 75 initial drying 24 hours 90 ? 98% rh 80 ? 98% rh temperature tolerance 2 c (3.6 f) unless otherwise specified initial measurements as specified in 2.2 0 step1 step3 step2 prior to first cycle only step4 one cycle 24 hours; repeat as specified in 2.5 voltage applied as specified in 2.4 circulation of conditioning air shall be at a minimum cubic rate per minute equivalent to 10 times the volume of the chamber step6 step7 hbk073 step5 51015 end of final cycle; measurements as specified in 2.7 optional sub-cycle if specified (2.3); sub-cycle performed during any 5 of the first 9 cycles; humidity uncontrolled during sub-cycle 20 time [h] temperature [ c] 25 50 25 0 90 ? 98% rh 90 ? 98% rh + 10 c ( + 18 f) ? 2 c ( ? 3.6 f) 80 ? 98% rh rate of change of temperature is unspecified, however, specimens shall not be subjected to radiant heating from chamber conditioning processes fig. 6 moisture resistance test requirements
series yc/tc 164 (pb free) product specification 8 8 w ww.yageo.com mar 01, 2005 v.2 chip resistor surface mount revision history revision date change notification description version 2 mar 01, 2005 - - new datasheet for 4 x 0603 thick film 1% and 5% with lead-free terminations - replace the 4 x 0603 part of pdf file: arc241_242_arv241_242_51_l_0.pdf - test method and procedure updated version 0 dec 05, 2003 - -
|
